Why Composite Deck Boards Need Room to Move Through a Wisconsin Winter

That little gap where two composite deck boards meet can look bigger in February than it did when you set out the patio chairs last summer. A change in the gap can be part of the way the boards respond to temperature. A joint that closes up, a board end that lifts, or a fastener that comes loose deserves a closer look. The useful question is what changed, where it happened, and whether the boards still have room to move. 

In Madison, the National Weather Service puts the normal daily high at about 27°F in January and 82°F in July, based on its 1991–2020 climate normals. That’s a difference of about 55°F between the two monthly averages. The numbers describe the air in Madison. They can’t tell you the temperature of a board sitting in full sun or how much a particular product will move. National Weather Service climate normals 

Why the gaps change through the seasons 

Composite decking generally gets longer as it warms and shorter as it cools. At an end joint, where two boards meet, the space between them gives the ends somewhere to go as the boards warm. A longer board can change length more than a shorter one made of the same material with the same temperature change. That’s one reason a long run along the edge of the deck may be worth watching. 

The temperature when the boards go down matters too. A board fitted on a cold morning may need more room to grow into as the weather warms. A board fitted in summer will have started out warmer. This guide to how composite decking expands explains how installation temperature and the position of a gap affect the layout. For your own deck, use the instructions for its exact board, fasteners and framing. 

Look at three different spaces 

A gap between the long sides of two boards serves a different purpose from the space where their ends meet. A third space may be needed where decking meets something fixed, such as a wall or post. Even on one deck, the manufacturer can give different sizes for all three. A measurement at one spot won’t tell you what the other two should be. 

Think about the places you’ll cover when the furniture goes out. This Wisconsin Mommy backyard makeover reminds you how quickly chairs and other outdoor pieces can change the view of a space. Before setting up for spring, take a look at a few board ends, including the edge near the house and a joint that will sit under the seating area. 

What a sixteenth of an inch looks like in practice 

One Trex installation guide gives a useful example in its section on metal framing. It lists an end-to-end installation gap of 1/8 inch above 40°F and 3/16 inch below 40°F. The second space is 1/16 inch wider. Those figures show how one manufacturer changes a fitting instruction for cold conditions on the setup described. Use the current instructions for your own system when planning a new installation. Trex installation guide 

That sixteenth of an inch is the difference between two installation instructions. The movement you see on a finished deck depends on the board, its length, how it’s fixed, and the temperatures it experiences. A gap you measure in January can be a useful record for another check in spring. To make sense of it, compare the same joint and take note of the conditions on both days. 

If you’re getting quotes for a new deck, ask which installation guide the contractor is using and where the drawing shows the end joints. A long border board that runs across the ends of other boards is worth pointing out. Ask how the builder will leave room for movement at that meeting point. It’s easier to discuss on a plan while there’s still time to change the layout. 

What to look for on an existing deck 

Look from a stable spot when the deck is clear of snow and ice. If you notice movement underfoot, keep people away from the affected area until a deck contractor can check it. If the deck looks sound and you’re simply curious about a joint, make a short record you can use again. 

  • Pick two or three places. Choose an end joint, a board near the house and, if you can see one, a joint on a long run. 
  • Record the conditions. Write down the date, the outdoor temperature, and whether the boards are sitting in sun or shade. 
  • Photograph the same joint. Put a ruler alongside the gap if you can do it safely. Keep the camera angle similar so you can tell whether the opening actually changed. 
  • Note anything that has shifted. A raised edge, a board pressing against trim, or a fastener that looks out of place is worth pointing out to the installer. 

A similar change across several joints may suggest seasonal movement. A problem in one place, especially if a joint closes up or one end rises, is a reason to have that spot checked. A contractor can look at the board ends and what supports them underneath. Share your photos and say when you first noticed the change. That’s more useful than trying to open a joint with a tool or driving in another screw. 

Set up a spring check before the snow arrives 

Keep the product name and the installation instructions with your house records. If you inherited the deck and don’t know the make, look for old paperwork or ask the previous installer if you have their details. Put one photo of each joint you want to watch in the same folder. That gives you something specific to check as the weather warms. 

Wisconsin Mommy’s guide to protecting outdoor plumbing before freezing weather is one place to start a fall checklist. Add a quick look at the boards while you’re packing away the hose. When the patio chairs come back out, check those same spots before they get covered. If a gap has changed but the boards still sit flat, you have a record to compare with the maker’s guidance. If an end is pushing up or something feels loose, show the installer exactly where it happened.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.